Parts & Accessories

- Proprietary 6mm thick (standard is 4mm) 7075 aluminum nipple offering the strength of a brass nipple while saving 20 grams per wheel, plus more pivot range at the spoke hole for reduced stress on spoke - Only for use with Torque nipple specific rims. Sold in bags of 36 nipples - T-20 Torx broach for pre-tensioning, 3mm flats for fine adjustment - See Tools - Wheelbuilding section for Atomlab Torque nipple tools

- Converts Atomlab 12x135mm thru-axle rear hubs to 10mm bolt-on axle - Includes (1) axle, (2) hex cap bolts and (2) washers

CNC machined from 6061-T6 aluminum alloy, Box One Schrader Valve Caps add a touch of style to any bike. Available in anodized red, blue, and black with laser-etched Box logos.

- Plastic spoke covers in a variety of colors - 300mm cut to fit length - 36 pieces - enough for one wheel - Increases visibility and demands attention

Replacement parts for Micro C-Drive Hubs. - Supplier Part: Replacement #16 Clutch Ring

- Grade 3 balls and magnetite rust proof finish - Abec 5 precision and silicone w seals - 3 times cryogenic race treatment - Bearings sold individually, not as pair

Designed to conform to the center channel and bead locking rim bed, Boyd tubeless tape creates an air-tight seal between the tire and rim bed. - Not as stiff as a lot of the other options, which makes installation a breeze!

- Designed to conform to the center channel and bead locking rim bed, Boyd tubeless tape creates an air-tight seal between the tire and rim bed. - Not as stiff as a lot of the other options, which makes installation a breeze!

The square bottom on the rubber, plus the rubber extending down the valve helps create the best airtight sealing system. Set up is a breeze and works much better than other valves on the market. - 44mm valve for 28mm carbon, Altamont, Altamont, CCC, and MTB wheels - 60mm valve for 44mm carbon and 36mm depths (36 Road Disc, Pinnacle, and Jocassee) - 80mm valve for 55 Road Disc and 60mm carbon - 110mm valve for 90mm carbon and 90 Road Disc - Weights for the valve (with nut for tightening) is: 44mm—5g, 55mm—5g, 60mm—6g, 80mm—6g, 110mm—8g

Bora valve bushings prevent the valve from rattling inside the valve hole. - Box of 5

Front disc brake quick release conversion kit from Campagnolo. - Convert Campagnolo Bora and Shamal disc brake wheels from thru-axle to quick release - Includes axle, end caps and adjusting sleeve - Quick release sold separately

Quick release conversion kit for disc brakes. - Convert Campagnolo Bora and Shamal disc brake wheels from thru-axle to quick release - Includes axle, end caps and adjusting sleeve - Quick release sold separately

- USB and Cult ceramic renewing kits can be used to upgrade Campagnolo wheels that come stock with stainless steel bearings - Kit includes (2) each of dust seals, hub cones, hub cups, and ceramic or steel ball bearings

Thru Axle for HELM suspension forks. - Compatible only with Cane Creek HELM forks

Upgrade your Mavic wheels with a CeramicSpeed Wheel Kit to reduce friction, increase performance, and get the most out of your Mavic Wheels immediately. The high velocity of wheel bearings means that bearing friction can have a huge impact on performance. CeramicSpeed Wheel Bearings have a proven lifespan, which is 3-5 times longer than standard wheel bearings. In The Box: - 3 x 61901 bearings - 2 x 608/9 bearings - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet - Front hub bearings: 61901 + 61901 - Rear hub bearings: 61901 + 608/9 + 608/9 Remember to add grease and mount seals before installation.

Choose to ride even faster by using CeramicSpeed Hub Bearings in your wheels. The DT Swiss-1 wheel kit fits 240s Road hubs, which are used by many wheel brands. Other kits are available for disc wheels and DT180 as well. The high velocity of wheel bearings means that bearing friction can have a huge impact on performance. CeramicSpeed Wheel Bearings have a proven lifespan, which is 3-5 times longer than standard wheel bearings. In The Box: - 2 x 61802 bearings - 2 x 61803 bearings - 2 x 61902 bearings - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet Remember to add grease and mount seals before installation.

Choose to ride even faster by using CeramicSpeed Hub Bearings in your wheels. The DT Swiss-3 wheel kit fits 240s Disc hubs. Other kits are available for DT 240s rim brake hubs, and DT180 as well. The high velocity of wheel bearings means that bearing friction can have a huge impact on performance. CeramicSpeed Wheel Bearings have a proven lifespan, which is 3-5 times longer than standard wheel bearings. In The Box: - 2 x 61903/18 bearings - 2 x 61802 bearings - 2 x 61902 bearings - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet Remember to add grease and mount seals before installation.

Optimize your Zipp wheels with CeramicSpeed Hub Bearings to benefit from reduced friction and increased performance. The result is higher speed with the same effort as well as a higher top speed. CeramicSpeed Wheel Bearings have a proven lifetime, which is 3-5 times longer than standard bearings. All components are optimized for low friction and prolonged lifetime. This wheel kit is compatible with 2015 & forward (77/177 hubs) + Mid 2018 & forward NSW Rim Brake Hubs. In The Box: - 4 x 61803 bearings - 2 x 61903 bearings - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

Optimize your Zipp wheels with CeramicSpeed Hub Bearings to benefit from reduced friction and increased performance. The result is higher speed with the same effort as well as a higher top speed. CeramicSpeed Wheel Bearings have a proven lifetime, which is 3-5 times longer than standard bearings. All components are optimized for low friction and prolonged lifetime. This wheel kit is compatible with 1st generation non-disc Zipp NSW (before mid-2018). In The Box - 4 x 61803 bearings - 1 x 61903 bearing - 1 x 61804 bearing - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

Optimize your Zipp wheels with CeramicSpeed Hub Bearings to benefit from reduced friction and increased performance. The result is higher speed with the same effort as well as a higher top speed. CeramicSpeed Wheel Bearings have a proven lifespan, which is 3-5 times longer than standard bearings. All components are optimized for low friction and prolonged lifetime. This kit is compatible with 2015+ (77/177 hubs) disc brake hubs & NSW Disc. In The Box - 4 x 61903 bearings - 2 x 61803 bearings - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

These kits convert Crankbrothers rear hubs to 12mm thru axle and 10mm QR spacing. - 135×10QR – 2017 3 & 11 kit (SKU 99204) compatible with: Level 3 & 11 4th generation (2017+) hubs - 142/148×12TA – 2017 3 & 11 kit (SKU 99205) compatible with: Level 3 & 11 4th generation (2017+) hubs - weight 23g per pair

Front axle and endcap kits for all non-boost 2017 cobalt, iodine, and zinc wheels. Use this front axle and endcap kit to convert any non-boost 2017 cobalt, iodine, or zinc wheel to the size selected below.

9/15/20mm conversion kit for current generation front hubs - Cobalt endcaps – These kits convert current generation Cobalt front wheels to 9/15mm thru-axle. - Iodine/Opium endcaps - These kits convert current generation Iodine and Opium front wheels to 9/15/20mm thru-axle. - Conversion: 9/15/20mm - Cobalt weight: 26g (9mm) / 16g (15mm) - Iodine/Opium weight: 28g (9mm) / 18g (15mm) / 23g (20mm)

Converts cobalt/iodine/opium hubs from 142 to 135 qr spacing. Rear endcaps kit – this kit converts any crankbrothers 2, 3, or 11 wheelset from 142×12mm thruaxle rear spacing to 135×9mm qr rear spacing. Conversion: 135x9 mm Weight: 23g per pair

Replacement Freehub body for I9 Hydra, I9 1/1, and Crankbrothers Hubs - Shimano MS/Synthesis Base Steel Driver

Replacement Freehub body for I9 Hydra, I9 1/1, and Crankbrothers Hubs - XD/Synthesis Base Steel Driver

A safe haven for your wheelset. - Soft protective wheel bag for safe transport of two wheels up to 29 inches. - Engineered for Crankbrothers by EVOC. - Durable, water resistant construction made from polyurethane coated 600D polyester - Internal divider keeps wheels protected from each other - Integrated pocket for stowing small items - Integrated axle protection - Integrated carry handles

Replacement Freehub body for I9 Hydra, I9 1/1, and Crankbrothers Hubs - Shimano MS/Synthesis Base Alloy Driver

- Replaces freehub body on current Cobalt or Iodine wheels with SRAM XD compatible body

Ease of use, lightweight, and optimum performance in a single product. The DT Pro Head shape, combined with both a torx and a square tool interface, makes wheel building a lot easier. The spherical contact surface aligns the nipple perfectly with the spoke. All-brass nipples are recommended for e-bike use. Weight: starting at 26g for 64 nipples.